# 车削加工经验总结

**URL:** <https://www.cax.do/t/experience-summary-of-turning-processing/90>\
**Category:** Programming\
**Created:** [2024 年11 月 3 日 04:04 UTC](https://www.cax.do/t/experience-summary-of-turning-processing/90 "2024-11-03T04:04:34Z")\
**Posts on this page:** 1\
**Page:** 1

<div class="post-metadata">

作者： ![Max](https://www.cax.do/user_avatar/www.cax.do/max/32/257_2.png) [@Max](https://www.cax.do/u/Max)\
发布日期： [2024 年11 月 3 日 04:04 UTC](https://www.cax.do/t/experience-summary-of-turning-processing/90/1 "2024-11-03T04:04:34Z")

</div>

When cutting metal, the tool’s angle during its entry into the workpiece is an important parameter that determines the geometric shape of the tool’s cutting part.

 ![image](https://www.cax.do/uploads/default/original/1X/3100e91bf9e51ac6c807a6ffad38f22a0fe81fca.jpeg)

### 1. Composition of the Cutting Part of a Lathe Tool

**Three Surfaces, Two Edges, and One Tip**

The cutting part of a lathe tool consists of the front face, main flank, secondary flank, main cutting edge, secondary cutting edge, and the tip.

 ![image](https://www.cax.do/uploads/default/original/1X/7392d99cb725f4f2171adf7026589ee9dedea640.jpeg)

1. **Front Face** : The surface on the tool where the chips flow over.
2. **Main Flank** : The surface on the tool that faces the machined surface of the workpiece and interacts with it.
3. **Secondary Flank** : The surface on the tool that faces the already machined surface of the workpiece and interacts with it.
4. **Main Cutting Edge** : The line where the front face meets the main flank is known as the main cutting edge.
5. **Secondary Cutting Edge** : The line where the front face meets the secondary flank is known as the secondary cutting edge.
6. **Tip** : The intersection of the main and secondary cutting edges is referred to as the tip. The tip is actually a small segment of a curve or line, called a rounded tip or chamfered tip.

### 2. Auxiliary Planes for Measuring Cutting Angles

To determine and measure the geometric angles of the lathe tool, three auxiliary planes are selected as references: the cutting plane, base plane, and orthogonal plane.

1. **Cutting Plane** : A plane that intersects the main cutting edge at a selected point and is perpendicular to the bottom plane of the tool holder.  

2. **Base Plane** : A plane that passes through a selected point on the main cutting edge and is parallel to the bottom plane of the tool holder.  

3. **Orthogonal Plane** : A plane that is perpendicular to both the cutting plane and the base plane.  

These three coordinate planes are mutually perpendicular, forming a three-dimensional Cartesian coordinate system.

 ![image](https://www.cax.do/uploads/default/original/1X/eb57cb6ac5e9d075fefac01ba7ceea000943b2f9.jpeg)

### 3. Main Geometric Angles of the Lathe Tool and Their Selection

1. **Front Angle (γ0) Selection Principle**: The size of the front angle primarily addresses the balance between the strength and sharpness of the tool tip. Generally, for materials with high hardness, a smaller front angle is chosen, while for softer materials, a larger angle is preferred. Additionally, for rough machining, a smaller front angle is used, and for finishing, a larger angle is selected. The front angle is typically chosen between -5° and 25°.Usually, during the manufacturing of lathe tools, the front angle (γ0) is not pre-made but is achieved by grinding a chip fluting on the tool. This fluting, also called a chip breaker, serves to break chips to prevent entanglement, control the direction of chip flow, maintain the precision of the machined surface, reduce cutting resistance, and prolong tool life.  

2. **Back Angle (α0) Selection Principle**: The first consideration is the nature of the machining. For finishing, a larger back angle is chosen, while for roughing, a smaller angle is selected. The hardness of the material also plays a role; for harder materials, a smaller main back angle enhances the strength of the tool tip, whereas for softer materials, a larger angle may be selected. The back angle should not be zero or negative and is generally chosen between 6° and 12°.  

3. **Main Inclination Angle (Kr) Selection Principle**: The rigidity of the turning process system, consisting of the lathe, fixture, and tool, is the primary consideration. If the system is rigid, a smaller main inclination angle is preferred to enhance tool life, improve heat dissipation, and surface finish. When machining steps, a main inclination angle of 90° is used, while for intermediate cutting, it is usually around 60°. The main inclination angle typically ranges from 30° to 90°, with common values being 45°, 75°, and 90°.  

4. **Secondary Inclination Angle (Kr’) Selection Principle**: The tool, workpiece, and fixture must have sufficient rigidity to minimize the secondary inclination angle; otherwise, it should be larger. For finishing, a secondary inclination angle of 10° to 15° is suitable, while for roughing, around 5° is appropriate.  

5. **Edge Inclination Angle (λS) Selection Principle**: This primarily depends on the nature of the machining. For rough machining, where the workpiece exerts greater impact on the tool, λS should be ≤ 0°. For finishing, where the impact is less, λS should be ≥ 0°. Typically, λS is set to 0°. The edge inclination angle is usually selected between -10° and 5°.
